Browse all practice questions for the Rigging CML Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Rigging CML Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What is the weight of a single 4-foot by 10-foot sheet of 1/4-inch steel?
  • When chain is going to be used in below -40°F conditions, you must
  • What is the simplest reeving method in lifting systems?
  • Typically, in lifting and rigging operations, which type of wire rope is used?
  • What term describes the ratio of the bend diameter to the rope diameter?
  • Which hitch can cause significant wear on the inside of the eye where it contacts the sling body, particularly for wire rope?
  • What is the procedure for signaling during a lift when the operator's view is obstructed?
  • When verifying a sling tag on-site, which statement is most accurate?
  • What edge protection devices are commonly used with slings?
  • OSHA requires that the proof test verification be retained by which party?
  • Which condition indicates a potentially unsafe shackle before lifting?
  • What is the purpose of a test lift?
  • Which professional should be consulted if equipment used for a lift is unusual and nonconforming?
  • What Subpart is Signals for Cranes & Derricks in construction found under?
  • What type of socket uses molten zinc or resin to secure the end of a wire rope inside the socket?
  • During inspections, which item is checked for damage along with critical defects?
  • What does the term 'eye-to-eye' mean in sling construction?
  • The end travel for a hoist is defined by which mechanism?
  • With multiple leg slings, sling load calculations should be performed to ensure that individual legs of a sling are not overloaded, especially when connected to what type of loads?
  • In chemically active environments, which chain material is preferred?
  • The size of a fall zone depends on what factor?
  • Which step helps identify issues prior to the lift by simulating the operation?
  • What practice helps avoid shock loading?
  • In the block loading calculation, what does the term (load - lead-line force) represent?
  • Which Manila rope types may be used for lifting applications?
  • How should synthetic slings be stored after use?
  • When the sheave groove is too narrow, the rope wear in the groove is known as what?
  • What is dynamic loading and how does it affect lifting calculations?
  • What is the weight of a single 4-foot by 8-foot sheet of 1/16-inch steel?
  • No written plan or special precautions are usually required for which lifts?
  • Which of the following are signs that a synthetic sling is damaged and must be removed from service?
  • When planning a lift, how should you account for angles and alignment with shackles?
  • When lifting a load that may swing uncontrollably, which method is commonly used to control the load?
  • When selecting edge protection for a sling, which factor is most important?
  • In rope handling, which statement about the speed of sheaves in four-part configurations is true?
  • Binding is an indication that chain links have what?
  • What is the minimum force required to lift a 10,000-lb load using a four-part reeving system with plain bearing sheaves, given bend ratio 15 and a friction factor of 0.33?
  • Which standards are commonly referenced for rigging in North America?
  • Which condition would make a lift complex?
  • What is the term for the condition in which chain links bow inward and prevent adjacent links from moving freely?
  • What is the total weight of a bundle of 25 pieces of 20-foot long, 1/2-inch EMT conduit?
  • Why is equalized rigging important when using multiple slings?
  • What are the key elements to check during a pre-use inspection of rigging gear?
  • Hand-chain hoists must be hung in which orientation so the hand chain can rotate freely around the wheel?
  • If wear reduces a chain link thickness by 10%, what is the recommended course of action?
  • What is the purpose of recording gear ID, inspection date, findings, next inspection date, and action taken?
  • What safety factor is commonly used in most rigging applications?
  • Who determines the Working Load Limit (WLL) of a component?
  • What is the function of a spreader bar in a multi-sling lift?
  • How many standard signals must a qualified signalperson be familiar with?
  • If a load symmetry ensures central gravity along that dimension, what is the reason the gravity is located there?
  • Identification characters directly on chain links include which items?
  • A dolly with two forks that are hydraulically lifted above wheels is commonly called a:
  • Which description best captures the primary advantage of chain slings for rigging?
  • Which of the following statements correctly describes the purpose of lower limit switches?
  • Synthetic fiber slings may be used for hoisting personnel baskets.
  • Distinguish between rated capacity and actual load.
  • A category of knots that are used to tie the ends of two ropes together is called a what?
  • Chain costs are less than wire rope of similar strength. Which statement is correct?
  • What multiplier is used to convert lead-line force to block loading in a four-part system with a 40° lead line?
  • What is the process of compressing a socket onto the end of a rope called?
  • Slip clutches are designed to slip at the range of 110% to 125% of rated capacity. Which option represents the lower end of this range?
  • What is shock loading and how can it be mitigated on a lift?
  • If the input shaft rotates faster than the output shaft, which statement best describes the gear ratio?
  • What is a key method to prevent a load from swinging during hoisting?
  • Given a load W and a two-leg sling with leg angle α from vertical, what is the per-leg tension?
  • What is the purpose of sling load calculations when using multi-leg slings?
  • What should you do if you discover a load is not balanced during lift?
  • If a load is symmetrical along one dimension, where is the center of gravity likely located along that dimension?
  • Why is it important to maintain exclusion zones during hoisting operations?
  • Which of the following is not a corrosion indicator requiring retirement?
  • If a chain is needed in a chemically active environment, it may need to be made of a special alloy that is
  • What is Working Load Limit (WLL)?
  • A hand-chain hoist uses a rotation of a continuous loop to provide an input torque to a gear drive. What is that loop called?
  • Which of the following factors influence sling selection?
  • Why must you not lift with damaged or modified hardware?
  • The services of a qualified engineer are necessary if the lift uses equipment or procedures that are unusual and do not conform to established standards. When is this required?
  • What is the recommended approach to performing a pre-lift test lift?
  • Hardware components can be stored together in groups.
  • Complex lifts may require multiple signalpersons at different locations, such as what type of spaces?
  • What forms a loop at the end of a rope by splicing the rope end into the rope body?
  • Which sign indicates gouging on chain links?
  • The use of which alloy chains are available for use in environments where regular steel chains would be adversely affected by chemicals?
  • How should a shackle be installed to avoid unsafe loading?
  • Which limit switches prevent a hoist hook from impacting a hoist or boom?
  • Lifting force can be measured directly with which device?
  • How should you lift at an angle with an eyebolt?
  • What is an eye-to-eye sling and how is it used?
  • Where should synthetic slings be stored after use?
  • The upper limit switch serves to prevent damage by stopping movement before the load can contact which parts?
  • A hand-chain hoist must be hung vertically so that the hand chain can rotate around the wheel. Which of the following best describes this requirement?
  • On what is the chain sling specification identified by the manufacturer?
  • What is the mechanical advantage of a three-part reeving system?
  • What term describes when strands are forced apart and the core material is squeezed out from between the strands?
  • What should you check when inspecting a hook for safe operation?
  • What area condition is required by many cranes for initial assembly and operation?
  • Which scenario specifically requires sling load calculations?
  • The area inside the sling eye that comes into contact with the sling body is the primary wear zone when using wire rope.
  • In a three-part block-and-tackle arrangement lifting 1,200 lb with a 400 lb lead-line at 60° from vertical, what is the block loading estimate?
  • A six-by-seven rope indicates a six-strand rope with how many wires per strand?
  • Synthetic slings generally include warning yarns within the body that are not normally visible. What color are they?
  • Which term describes a pulley arrangement used with a manual hoist to gain mechanical advantage?
  • In sling selection, why is the load center of gravity important?
  • What is the purpose of identifying marks on Grade 80 and Grade 100 chain links?
  • Which type of wire rope is least susceptible to wear?
  • Who is authorized to shorten slings by knotting or twisting them?
  • According to ASME B30.9, chains should be removed from service if the thickness of any part of a link has decreased by what percentage?
  • What is the purpose of a lift plan in rigging operations?
  • When would you choose wire rope slings over chain slings?
  • In a hoist, distance relates to how many more times the input shaft must rotate for the output shaft to rotate once. Which is accurate?
  • In the listed sequence of wire rope damage, which item appears last?
  • What is a grab hook used for in rigging?
  • Which device is a dolly with two forks that are hydraulically lifted above a set of wheels, used to move palletized loads?
  • What is the maximum safe loading angle for a shackle?
  • End fittings are available for slings; most types are what shapes?
  • In configurations of four parts or more, which sheave moves fastest?
  • Which of the following indicates wear on a chain sling requiring retirement?
  • What does lift geometry refer to in the context of sling selection?
  • Which sign indicates bent links during chain inspection?
  • If a load has sharp edges or heat hazards, should you use a synthetic web sling?
  • Lifting chain is designed to elongate before fracturing as much as what percent?
  • When applying the choker hitch, care should be taken not to beat the sling down against the load. Which hitch is referenced?
  • What term describes a rope's tendency to rotate and untwist when under load?
  • In a four-part block-and-tackle arrangement, a 1,000 lb load is lifted with a 250 lb lead-line force at a 40° angle from vertical. What is the block loading estimate?
  • Which of the following is not typically a consideration for lattice-boom lifts?
  • What is a socket that is compressed onto the end of a wire rope called?
  • Which general requirements are commonly referenced alongside ASME B30 standards for rigging in North America?
  • Wire rope is composed of a core surrounded by strands, each consisting of wires of what characteristic?
  • Which rope type is noted as being least susceptible to wear and often cited in rigging references?
  • How do you verify a sling’s WLL on-site when you only have a tag?
  • Which hardware component can be used to prevent wear on the inside of the sling eye where it contacts the sling body?
  • Which of the following is not listed as a sign of chain damage?
  • What is the total material weight of a load consisting of 20 pieces of 4-foot by 10-foot steel sheets that are 1/4-inch thick, given 10.2 psf?
  • Identify the correct sequence of wire rope damage from top to bottom.
  • The ratio of the strength of a bent rope to its nominal strength rating is called what?
  • What is the total material weight of a load consisting of 35 pieces of 4-foot by 8-foot steel sheets that are 1/16 inches thick, given weight 2.55 psf per sheet?
  • Why should loads be lifted with the load’s center of gravity close to the lifting point?
  • A back splice is commonly done to tag lines on a working end in order to mark the end of the rope. Which option best completes this idea?
  • What is the purpose of inspection certification and records?
  • Which of the following is a common end fitting category used with slings?
  • During which signal must the signalperson watch for two-blocking?
  • Which component(s) are described in the material as limiting travel at both ends of the hoist path?
  • Which of the following actions is required before using chain in extremely cold conditions (below -40°F)?
  • What is the purpose of a nip in rope handling?
  • Which action is essential when the load is ready to be disconnected to ensure safety and accountability?
  • The ratio of the diameter of a bend to the nominal diameter of the rope is called what?
  • In an asymmetrical rigging with lift points 120 inches apart and the center of gravity located 40 inches from point B, for a 9,000-pound load, what is the weight experienced by point A?
  • Which types of signals may be useful in extremely noisy environments or areas with significant radio interference?
  • Which type of slings typically have greater friction with the load surface, helping keep them in place?
  • Which splice is typically used to create a loop at the end of a rope?
  • In a prelift check, what should be done prior to the actual lift to help identify issues?
  • Lower limit switches prevent a hoist from reaching the end of its what?
  • If diameter loss exceeds 10%, what action should be taken?
  • In wire rope, what is the component described as being surrounded by strands?
  • Which scenario best justifies selecting a synthetic web sling over other sling types?
  • A large rectangular load is lifted with a dynamometer showing 6,000 pounds at lift point A, and then 4,000 pounds at lift point B when the other end is lifted; the lift points are 120 inches apart. Where is the CG along its length from point A?
  • Which device is used to measure lifting force directly?
  • What is the role of a competent person in rigging operations?
  • The sling angle is defined as the acute angle between which two parts?
  • What should you establish to ensure clear communication during rigging operations?
  • Which sign indicates elongation in chain links?
  • Which references should be consulted for guidance on sling applications?
  • Chain slings are made by whom from lengths of chain and rigging hardware components?
  • Which sign indicates excessive wear on chain links?
  • Which option best describes the elongation behavior of lifting chain before fracturing?
  • Fiber ropes are typically rated for use in what temperature range?
  • Which component is used to identify the specifications of a chain sling?
  • What is the area in square feet of a 4-foot by 8-foot sheet?
  • What indicates you should retire a chain sling?
  • How should a hook’s safety latch be checked before a lift?
  • Which splice is commonly used to mark the rope’s end on the working line?
  • What is the correct procedure for disconnecting rigging after a lift?
  • If 1/2-inch steel EMT conduit weighs 0.30 pounds per foot, what is the total weight of a bundle of 75 pieces of 20-foot long, 1/2-inch conduit?
  • On some cranes, the upper limit switch mechanism is known as a(n) what?
  • Which items are part of the standard PPE for riggers?
  • How does sling angle affect the load in each leg of a two-leg sling?
  • Chain has approximately how many times the impact absorption capability and is more flexible than wire rope?
  • What corrosion indicators require retirement of rigging hardware?
  • Inspections are intended to identify critical defects to the equipment, including damage to which item?
  • What is the purpose of a swivel hoist ring or swivel point?
  • If a two-leg sling is vertical (angle from vertical is zero), what is the per-leg load relative to the total weight?
  • A four-part block-and-tackle assembly contains how many parts?
  • A three-part block-and-tackle assembly contains how many parts?
  • Why are tag lines used during lifts?
  • When should edge protection be used with slings and what forms can it take?
  • The heating method preferred because it fuses strands and strand wires together is which tool?
  • Identification on Grade 80 and Grade 100 chain links may include the manufacturer's mark, raised characters, traceability or date code. Which of the following is NOT a valid identification feature?
  • Which statement is true about shortening slings by knotting or twisting them?
  • In an asymmetrical rigging with lift points 120 inches apart and the center of gravity located 80 inches from point A, for a 9,000-pound load, what is the weight experienced by point B?
  • What methods help prevent a load from swinging during hoisting?
  • How do you determine if a shackle is properly rated for a given load?
  • The distance relationship in a hoist describes how many more input rotations are required for the output to complete one revolution. Which is accurate?
  • Rigging equipment should be kept in a designated and organized area that is clean, dry, and away from harmful what, or heat?
  • Web sling strength is based on which webbing material?
  • When consulting a sling load chart for rigging, which angle should be used if there are multiple?
  • What is a benefit of using the smaller angle on a sling load chart?
  • Which sling type is typically chosen for delicate loads to minimize edge damage?
  • Which lifting scenario would typically require a more cautious plan due to hazardous environment?
  • A sling load chart is used to determine capacity changes based on which variable?
  • Using U-bolt clips, the termination efficiency is approximately what?
  • To prevent slippage of a chain sling, a lifting beam may have to be utilized.
  • If the lead line of a single sheave is held vertically, how much force would the block experience when lifting a 100-lb load?
  • Why is it dangerous to use a lifting hook with a bent throat or a mismatched latch?
  • Which of the following best describes identification characters directly on chain links?
  • Lifting force can be measured directly with either a dynamometer or a [?].
  • In a hoist, the input shaft turns at a faster rate than the output shaft. Which shaft has the higher speed?
  • What is the purpose of the tag on rigging hardware?
  • How do you measure chain sling wear and when to retire?
  • Slip clutches are designed to slip at what percent of the hoist's rated capacity?
  • If rigging hardware shows deformation that affects geometry, what is the proper action?
  • Which area condition is essential for safe initial crane setup and operation?
  • If a piece of rigging gear shows wear beyond manufacturer limits, what is the proper action?
  • The output speed of a hoist is determined relative to the input speed by which of the following statements?
  • Cribbing used to support a load before and after a lift must be checked for sufficient capacity and what else?
  • What considerations are unique to lifting with a lattice boom or boom crane?
  • Chain for rigging is normally favored over wire rope because chain has approximately how many times the impact absorption capability?
  • How do weather and wind affect rigging operations?
  • Why is a safety factor applied to rigging hardware ratings?
  • Which treatment can be used to develop the desired combination of strength and durability in a metal?
  • A swivel hoist ring is used to prevent twisting of rigging when the load is rotated. Which option correctly states its primary purpose?
  • How do you ensure you have a clear path for a hoist?
  • Which combination of Manila rope types is acceptable for lifting applications?
  • Which hitch is typically the most stable way to rig a load for hoisting?
  • In crane operations, what term describes the total space required around the crane and its safe zone during operation?
  • A loss of diameter caused by corrosion that exceeds what percentage triggers removal from service?
  • A two-leg sling has the best load capabilities at how many degrees?
  • Which of the following correctly describes the typical sling end fittings shapes?
  • If the center of gravity is exactly midway between lift points A and B, what is the weight carried by each lift point for a 9,000-pound load?
  • What multiplier is used for a 60° lead line when calculating block loading?
  • Among three synthetic fiber ropes, which one outperforms the other two in most categories?
  • What is the purpose of a snatch block in lifting?
  • Chain sling legs may be shortened with what by the chain manufacturer or a qualified person?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy